Introduction
Welcome to this guide on how to get your tablet out of Fastboot mode.
However, sometimes users accidentally enter Fastboot mode or encounter issues that prevent them from exiting it.
Fastboot mode is a feature commonly found on Android devices, including tablets.
Its important to note that Fastboot mode is distinct from other boot modes like Recovery mode or Safe mode.
While Recovery mode is primarily used for system recovery and troubleshooting, Fastboot mode specifically deals with bootloader-related tasks.
Understanding the cause will help us in finding the appropriate solution to exit Fastboot mode on your tablet.
Unlike other boot modes like Recovery mode or Safe mode, Fastboot mode is specifically designed for bootloader-related operations.
When your rig is in Fastboot mode, it establishes a communication channel between your machine and the bootloader.
Entering Fastboot mode on your tablet may vary depending on the manufacturer and the machine model.
However, its crucial to note that Fastboot mode can be risky if not used properly.
Its essential to identify the cause to determine the most appropriate solution.
In the next section, we will explore different methods to exit Fastboot mode on your tablet.
Simply press and hold the power button until the rig powers off completely.
The key combination varies depending on the manufacturer and the rig model.
Press and hold the key combination until the tablet powers off and then release the keys.
Finally, press the power button to turn it back on and find out if it boots normally.
ADB allows you to communicate with your gear through a computer and execute commands.
This command instructs the gear to reboot, hopefully exiting Fastboot mode and booting into the regular operating system.
Its important to note that using ADB requires some technical knowledge and familiarity with command-line tools.
Heres how it’s possible for you to do it:
1.
Press and hold the power button on your tablet until the rig powers off completely.
You may need to hold the button for around 10-15 seconds.
Once the tablet is turned off, wait for a few seconds before proceeding to the next step.
Press the power button again to turn on your tablet.
Ideally, your tablet should now boot into the normal operating system, exiting Fastboot mode.
Sometimes, the power button may not respond as expected, resulting in difficulties in turning off the equipment.
These methods are discussed in the following sections.
c’mon note that the power button method may vary slightly depending on the tablets manufacturer and model.
Heres how you’re free to do it:
1.
Start by ensuring that your tablet is powered on and in Fastboot mode.
Look for the correct key combination to exit Fastboot mode.
The key combination may vary depending on your tablets manufacturer and model.
Press and hold the specific key combination simultaneously for a few seconds.
verify to hold the keys until the tablet powers off completely.
Press the power button to turn on your tablet.
Ideally, your tablet should now boot into the normal operating system, exiting Fastboot mode.
Sometimes, it may take a few attempts before successfully exiting Fastboot mode using the hardware keys.
If neither the power button method nor the hardware keys method worked for you, dont worry.
We will discuss this method in the next section.
ADB allows you to communicate with your Android machine through a computer and execute various commands.
Heres how you might use ADB to exit Fastboot mode:
1.
Ensure that you have ADB installed on your setup.
Connect your tablet to the computer using a USB cable.
Open a command prompt or terminal on your system.
Navigate to the directory where ADB is installed.
This is typically the platform-tools folder within the Android SDK installation directory.
In the command prompt or terminal, enter the commandadb devicesto peek if your machine is detected by ADB.
If your machine appears in the list of connected devices, youre ready to proceed.
Now, enter the commandadb reboot.
Wait for your tablet to complete the reboot process.
It may take a few moments for the tablet to start up and load the operating system.
If everything goes well, your tablet should now be out of Fastboot mode and running normally.
Using ADB commands to exit Fastboot mode is more advanced and requires some technical knowledge.
Here are some troubleshooting steps to consider:
1.
Check the Hardware:Ensure that the hardware buttons on your tablet are functioning correctly.
A faulty power button or volume key could be causing the rig to continuously enter Fastboot mode.
If necessary, consider getting the hardware checked or repaired by a professional.
Update ADB and Drivers:verify that you have the latest version of ADB installed on your system.
Additionally, ensure that the necessary drivers for your tablet are up to date.
Verify USB Connection:Check the USB cable and the connection between your tablet and the computer.
Try using a different USB cable or a different USB port on your box.
Retry the Methods:If the previous methods didnt work, its worth giving them another try.
They may be able to provide specific guidance or recommend a solution that is tailored to your gadget.
In this guide, we explored the various methods to exit Fastboot mode on your tablet.
We began by understanding what Fastboot mode is and how it differs from other boot modes.
The key combinations and procedures may vary depending on the tablets make and model.
Now, you might enjoy using your tablet without the limitations of Fastboot mode.
